How To Connect Jlab Go Air To Ipad

People are currently reading this guide.

👤

Published by A contributor at Hows.Tech sharing helpful insights.

📝 Article edited 0 times 🕒 Last modified by Default Author

You've just unboxed your sleek JLab Go Air earbuds, and you're eager to dive into your favorite podcasts, music, or video calls on your iPad. Excellent choice! The JLab Go Air are fantastic for on-the-go audio, and connecting them to your iPad is a straightforward process. Let's get you set up for a seamless listening experience.

Connecting Your JLab Go Air to Your iPad: A Comprehensive Guide

This guide will walk you through each step, ensuring you successfully pair your JLab Go Air earbuds with your iPad, along with some helpful tips and troubleshooting advice.

Step 1: Power Up and Prepare Your JLab Go Air

Before anything else, let's make sure your JLab Go Air earbuds are ready to be discovered.

Sub-heading: Unboxing and Initial Charge (if applicable)

If this is your very first time using your JLab Go Air, you might find a small plastic pull tab on the charging contacts of each earbud. Gently remove these tabs. These are there to prevent battery drain during shipping.
Once the tabs are removed, place both earbuds back into their charging case. The case lights should indicate they are charging (often a red light). Ensure the case itself has enough charge. If not, plug the case into a USB power source using the integrated USB cable until the case lights indicate a sufficient charge.

Sub-heading: Entering Pairing Mode

Open the Charging Case: Once your earbuds have a bit of charge (or if they're already charged), open the charging case.
Remove the Earbuds: Carefully take both JLab Go Air earbuds out of the charging case.
Automatic Pairing Mode: The JLab Go Air earbuds are designed to automatically enter Bluetooth pairing mode once they are removed from the case. You'll know they're in pairing mode because one of the earbuds will be blinking blue and white. This alternating light pattern signifies that they are ready to connect to a device. The other earbud will typically be solid white or off, indicating it's connected to its twin.

If you previously connected your JLab Go Air to another device, ensure that device's Bluetooth is turned OFF or that you have "forgotten" the JLab Go Air from its Bluetooth settings. This prevents the earbuds from automatically connecting to that device instead of your iPad.

Step 2: Prepare Your iPad for Connection

Now that your JLab Go Air earbuds are actively searching for a device, it's time to tell your iPad to look for them.

Sub-heading: Enabling Bluetooth on Your iPad

Go to Settings: On your iPad's home screen, tap the "Settings" app icon. It looks like a set of gray gears.
Navigate to Bluetooth: In the Settings menu, look for and tap on "Bluetooth" in the left-hand sidebar.
Toggle Bluetooth On: Make sure the Bluetooth toggle switch at the top of the Bluetooth settings screen is in the "On" (green) position. If it's already on, simply leave it.

Step 3: Pairing Your JLab Go Air with Your iPad

This is where the magic happens! Your iPad will now scan for available Bluetooth devices.

Scan for Devices: Once Bluetooth is enabled on your iPad, it will automatically start searching for nearby Bluetooth devices. You should see a section labeled "Other Devices" or similar.
Select "JLab GO Air": In the list of available devices, you should see "JLab GO Air" appear. Tap on it to initiate the connection.
Confirm Connection: Your iPad will attempt to connect to the JLab Go Air earbuds. Once successfully connected, you'll typically hear a voice prompt from your JLab Go Air saying, "Bluetooth connected". On your iPad, "JLab GO Air" will move from "Other Devices" to "My Devices" and will show "Connected" next to it. The blinking blue and white light on the earbud will also stop and become a solid white light (or turn off).

Congratulations! Your JLab Go Air earbuds are now paired and ready to use with your iPad.

Step 4: Testing and Enjoying Your Audio

Now that you're connected, let's make sure everything sounds perfect.

Play Some Audio: Open any app on your iPad that plays audio – Spotify, Apple Music, YouTube, a video, etc. Start playing something.
Adjust Volume: Use the volume buttons on your iPad to adjust the playback volume. You can also use the touch controls on your JLab Go Air earbuds themselves for volume control (refer to your JLab Go Air manual for specific touch control functions, but typically a single tap on the left earbud decreases volume and a single tap on the right earbud increases it).
Check for Calls: If you receive a call on your iPad (e.g., FaceTime audio), your JLab Go Air earbuds should automatically route the audio and microphone for the call.

Troubleshooting Tips: When Things Don't Go as Planned

Sometimes, technology can be a little temperamental. If you're having trouble connecting, try these troubleshooting steps:

Ensure Proximity: Make sure your JLab Go Air earbuds and iPad are close to each other (within a few feet) during the pairing process.
Reboot Both Devices: A simple restart can often resolve minor glitches.
- For JLab Go Air: Place both earbuds back in the charging case, close the lid, wait a few seconds, then take them out again.
- For iPad: Turn off your iPad completely and then turn it back on.
Forget the Device and Re-pair: If you've tried connecting before and it failed, or if you're having issues, "forgetting" the device can give you a fresh start.
1. On your iPad, go to Settings > Bluetooth.
2. Tap the "i" icon next to "JLab GO Air" under "My Devices".
3. Tap "Forget This Device". Confirm your choice.
4. Then, repeat Step 1, 2, and 3 of this guide to re-pair.
Reset JLab Go Air (Manual Reset): This is a more drastic step but can be very effective for persistent pairing issues or if the earbuds seem disconnected from each other.
1. Keep the earbuds in the charging case.
2. Forget "JLab GO Air" from your iPad's Bluetooth settings (as described above).
3. Quick tap 7 times on one earbud in the charging case. The earbud will blink blue 4 times.
4. Quick tap 7 times on the other earbud in the charging case. That earbud will also blink blue 4 times.
5. Take both earbuds out of the charging case. One earbud should be solid white, and the other will blink blue/white, indicating it's ready to pair.
6. Proceed with Step 3 to connect to your iPad.
Check for Interference: Other Bluetooth devices or Wi-Fi networks in the vicinity can sometimes cause interference. Try moving to an area with less electronic clutter.
JLab Support & Manual: If all else fails, consult the official JLab support website or the full user manual that came with your JLab Go Air for model-specific troubleshooting.

10 Related FAQ Questions

How to check if my JLab Go Air earbuds are charged?

Place both earbuds in the charging case. A red light on the case usually indicates the earbuds are charging. The case itself will often have indicator lights (e.g., pulsing blue while charging, solid blue when fully charged) to show its battery level.

How to know if my JLab Go Air is in pairing mode?

When taken out of the charging case, one of the JLab Go Air earbuds will display a blinking blue and white light pattern, indicating it's actively searching for a device to pair with.

How to reconnect JLab Go Air to my iPad after initial pairing?

Once paired, simply take your JLab Go Air earbuds out of their charging case. They should automatically power on and reconnect to your iPad if your iPad's Bluetooth is on and it's the last connected device.

How to switch JLab Go Air between multiple devices (e.g., iPad and iPhone)?

The JLab Go Air can only be connected to one Bluetooth device at a time. To switch, first turn OFF Bluetooth on the previously connected device (e.g., your iPhone). Then, turn ON Bluetooth on your iPad and select "JLab GO Air" from the list of available devices to connect.

How to adjust the volume on JLab Go Air?

You can adjust the volume directly on your iPad using its volume buttons. Alternatively, with JLab Go Air, a single tap on the left earbud decreases volume, and a single tap on the right earbud increases volume.

How to answer a call with JLab Go Air?

Typically, a single tap on either earbud will answer an incoming call.

How to use only one JLab Go Air earbud?

Yes, the JLab Go Air allows for independent use. Simply take one earbud out of the charging case, and it will connect to your iPad. The other earbud can remain in the case.

How to factory reset JLab Go Air earbuds?

While in the charging case, forget "JLab GO Air" from your iPad's Bluetooth. Then, quick tap 7 times on one earbud, wait for 4 blue blinks, then quick tap 7 times on the other earbud, wait for 4 blue blinks. Take both out of the case; one will be solid white and the other blinking blue/white, ready to re-pair.

How to troubleshoot if JLab Go Air is not showing up on my iPad's Bluetooth list?

Ensure the earbuds are out of the charging case and one earbud is blinking blue/white. Check that your iPad's Bluetooth is ON. Try restarting both devices (iPad and earbuds). If issues persist, perform a manual reset of the earbuds.

How to update the firmware on my JLab Go Air?

Firmware updates for JLab products are typically managed through the JLab Audio App (if available for your specific Go Air model) or by visiting the official JLab support website. Check their site for specific instructions related to your JLab Go Air model.

5726240709100750284